Hoppa till innehåll
Free shipping on orders over 3000 SEK excl. VAT! Volume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%
Volume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%Shiny solder joints and uneven surfaces: how to get a measurable image without glare and blurry edgesLive Full HD Image Straight on the Screen: Skip the Computer When Inspecting Small DetailsThe measurement field no one sees: when magnification is entered by hand, the measurement goes wrongFrom suspected damage to a measurable image: a digital microscope that works with or without a computerSharp images and measurements on an uneven, glossy surface: how to solve what a magnifier and the naked eye can’tReflections hide the defect: how to inspect shiny metal and plastic surfaces without glareReflections in shiny metal hide the flaw: how to see the surface with polarized light and measure directly in the imageCrack magnifier with a stainless steel scale: how to tell whether the crack is 0.2 mm or 0.4 mmMeasurement errors in microscope images often start with a magnification that someone forgot to recordShiny metal surfaces hide defects behind reflections – here’s how to see them anyway at the benchVolume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%Shiny solder joints and uneven surfaces: how to get a measurable image without glare and blurry edgesLive Full HD Image Straight on the Screen: Skip the Computer When Inspecting Small DetailsThe measurement field no one sees: when magnification is entered by hand, the measurement goes wrongFrom suspected damage to a measurable image: a digital microscope that works with or without a computerSharp images and measurements on an uneven, glossy surface: how to solve what a magnifier and the naked eye can’tReflections hide the defect: how to inspect shiny metal and plastic surfaces without glareReflections in shiny metal hide the flaw: how to see the surface with polarized light and measure directly in the imageCrack magnifier with a stainless steel scale: how to tell whether the crack is 0.2 mm or 0.4 mmMeasurement errors in microscope images often start with a magnification that someone forgot to recordShiny metal surfaces hide defects behind reflections – here’s how to see them anyway at the bench

Crack Loupe RL-8 with 45°-Angled Stainless Steel Scale 0.1 mm: When Measuring Cracks in Concrete or Cutting Edges on Drill Bits Requires an Aplanatic Loupe That Does NOT Scratch Like Glass

Published 13 July 2026 at 11:46

A construction technician who needs to measure crack width in concrete has traditionally had four options: a ruler (0.5 mm reading), a caliper (difficult to position in a crack), a digital crack gauge (SEK 5,000-15,000) or a crack magnifier for SEK 1,200-4,000. The crack magnifier wins for field QC because it is portable, mechanically robust, and reads with 0.1 mm precision directly in the crack.

The RL-8 is the 8x version of the Swiss classic crack magnifier series (also available as 6x and 10x). The design has three key differentiators compared to a standard measuring loupe.

Stainless steel scale instead of glass

Most measuring loupes (Peak Lupe, the KIMAG series) have a glass scale at the base. Glass has two advantages: it is completely transparent, and the graduations are etched with high precision. But glass also has a drawback that becomes dominant in daily field use: it scratches.

Contact surfaces that damage a glass scale:

  • Concrete surfaces with sand particles.
  • Sharpened drill bit edges (the cutting edge is harder than glass).
  • Carbide milling flutes.
  • Grinding stone surfaces during tool inspection.
  • Roughness standards in the workshop lab.

After 3-6 months of daily field use, a glass scale has visible scratches that interfere with reading. Replacement costs SEK 200-500 each time.

The RL-8 instead has a stainless steel scale with etched graduation (0.1 mm divisions, 0.02 mm line width). Steel withstands wear from concrete, carbide and abrasives without the markings being rubbed off. The scale can be replaced as a spare part should it be damaged.

45° angle: two complementary effects

Standard measuring loupes have the scale flat at the base (0°) — in direct contact with the workpiece. The RL-8 crack magnifier has the scale angled at 45°. This gives two effects:

Effect 1: An opening for light. When the scale sits flat, it blocks ambient light. The light must come from the loupe itself (LED, if fitted) or from an angle above the loupe lens. With the 45° angle, a gap opens up beneath the scale where ambient light (daylight, workshop lighting) enters and illuminates the measuring surface. No external lighting is required.

Effect 2: Reflection elimination. A flat scale reflects direct light straight back toward the eye, glaring the reading. The 45° angle deflects the reflection to the side, away from the eye. Result: the scale is clear even in direct sunlight on construction sites.

Aplanatic lens

”Aplanatic” means corrected for both spherical aberration AND coma. An ordinary singlet loupe is corrected for spherical aberration in the center but distorts toward the edges of the field of view — straight lines curve and circles become oval.

The RL-8 crack magnifier has a multi-element construction that maintains accuracy across the entire 20 mm field of view. The practical consequence: a crack measured at the edge of the field of view gives the same reading as a crack measured in the center. No manual centering is required.

A line width of 0.02 mm in the graduation means the reading can be interpolated to ~0.03-0.05 mm precision, considerably better than the nominal 0.1 mm graduation steps suggest.

Adjustable focus (sliding focus)

The height-adjustable lens system allows focusing on uneven measuring surfaces. This is practically important for:

  • Concrete cracks that lie below the surface level (the scale rests against the outer edge, the crack is 1-3 mm inside).
  • Drill bit edges where the cutting edge is turned into the surface.
  • Milling cutter edges with conical geometries.

Standard measuring loupes (Peak Lupe 1976, 1998) have fixed focus — they must be held at exactly the specified working distance (typically 10-15 mm) for a sharp image. The RL-8’s adjustable focus tolerates ±3-5 mm variation without loss of sharpness.

Areas of application

Construction QC — crack measurement in concrete:

  • Standard EN 1992-1-1 requires documentation of crack width in load-bearing concrete structures.
  • Classification: hairline (<0.1 mm), micro (0.1-0.3 mm), visible (0.3-1.0 mm), dangerous (>1.0 mm).
  • A crack magnifier with 0.1 mm graduation provides direct visual classification according to the standard.

Toolmaker QC — cutting edge inspection:

  • Drill bit cutting edges: measuring edge radius and micro-chipping after use.
  • Milling cutting edges: checking flank wear and crater wear.
  • Lathe tool measurement: verifying chip breaker geometry.

Metallurgy and materials testing: Evaluation of crack propagation in fatigue test specimens.

Electronics manufacturing: PCB crack inspection — hairline cracks in solder traces after thermal cycling.

Restoration: Inspection of cracks in historic stone monuments, concrete sculptures and historic mortar joints.

Automotive industry: Post-collision inspection of chassis weld seams to detect micro-cracks.

Nuclear power QC: Routine visual inspection of pipe weld seams where micro-cracks may indicate stress corrosion.

Specifications

  • Magnification: 8x (aplanatic, distortion-free).
  • Field of view: 20 mm diameter.
  • Working distance: 10 mm.
  • Scale: 0.1 mm graduation, 0.02 mm line width, stainless steel, etched, 45° angled.
  • Focusing: height-adjustable lens system (sliding focus).
  • Body: all-metal construction (robust for field use).
  • Size: 32 × 50 mm.
  • Weight: 37 grams (fits in a breast pocket).
  • Plastic case for storage included.
  • Spare scale can be ordered separately.

Alternatives and options

Switching to a different magnification: The RL-B series is available in 6x, 8x and 10x. The 10x version (RL-B-10) costs SEK 3,715 and has a 12 mm field of view — better for very small cracks but with less overview.

LED lighting: Available as an option for measurements in dark spaces (cave-like underground areas, tank interiors, basement spaces).

Alternative tools:

  • Digital crack gauge with camera: SEK 8,000-25,000. Advantage: image documentation. Disadvantage: requires a battery and calibration, and is more fragile.
  • Crack microscope 20-60x: SEK 3,000-8,000. Advantage: higher magnification. Disadvantage: requires a stand or a very steady hand.

What you get for your money

Classic Swiss crack magnifier RL-8, 8x aplanatic magnification, 20 mm field of view, 0.1 mm stainless steel scale with 45° angle, sliding focus, all-metal construction, plastic case, spare scale available as a separate part. SEK 1,574.

The standard tool for crack measurement on construction sites, toolmaking workshops, restoration projects and other field applications where a crack magnifier needs to withstand daily wear without the scale being destroyed. The price premium over a standard measuring loupe (SEK 400-900) is justified by the wear resistance of the stainless steel scale (2-4 times longer service life before a scale replacement is needed) and the 45° angle’s effective design in variable lighting conditions.

Read more: Crack magnifier RL-8 in the shop →

More news

All news