Hoppa till innehåll
Free shipping on orders over 3000 SEK excl. VAT! Volume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%
Volume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%The glare on the metal surface hides the scratch: how the polarizer in a handheld digital microscope reveals what a loupe and the eye missShiny solder joints and uneven surfaces: how to get a measurable image without glare and blurry edgesLive Full HD Image Straight on the Screen: Skip the Computer When Inspecting Small DetailsThe measurement field no one sees: when magnification is entered by hand, the measurement goes wrongFrom suspected damage to a measurable image: a digital microscope that works with or without a computerSharp images and measurements on an uneven, glossy surface: how to solve what a magnifier and the naked eye can’tReflections hide the defect: how to inspect shiny metal and plastic surfaces without glareReflections in shiny metal hide the flaw: how to see the surface with polarized light and measure directly in the imageCrack magnifier with a stainless steel scale: how to tell whether the crack is 0.2 mm or 0.4 mmMeasurement errors in microscope images often start with a magnification that someone forgot to recordVolume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%The glare on the metal surface hides the scratch: how the polarizer in a handheld digital microscope reveals what a loupe and the eye missShiny solder joints and uneven surfaces: how to get a measurable image without glare and blurry edgesLive Full HD Image Straight on the Screen: Skip the Computer When Inspecting Small DetailsThe measurement field no one sees: when magnification is entered by hand, the measurement goes wrongFrom suspected damage to a measurable image: a digital microscope that works with or without a computerSharp images and measurements on an uneven, glossy surface: how to solve what a magnifier and the naked eye can’tReflections hide the defect: how to inspect shiny metal and plastic surfaces without glareReflections in shiny metal hide the flaw: how to see the surface with polarized light and measure directly in the imageCrack magnifier with a stainless steel scale: how to tell whether the crack is 0.2 mm or 0.4 mmMeasurement errors in microscope images often start with a magnification that someone forgot to record

Peak 1972-100 Glass Measuring Ruler 100 mm with 15× Magnifier: When an Etched Scale with 0.1 mm Graduation Slides Directly onto the Workpiece and the Magnifier Glides Over for Sub-Millimeter Readings

Published 8 July 2026 at 07:27

Direct-contact measurement on a work surface is one of the classic metrology tasks where a mechanical caliper or micrometer doesn’t work. The caliper requires the jaws to be set against raised reference edges — but if the measurement is the distance between two points (two cracks, two markers, two defects), there is no raised surface for jaws to grip. The classic solution: a transparent glass ruler with an etched scale is placed directly over the surface; the operator sees both points through the glass and reads their position on the scale. With a 15× loupe sliding over the scale, sub-millimeter accuracy becomes easy to read.

What the Peak 1972-100 is

Glass measuring ruler with 0.1mm scale division, including 1 loupe with 15x magnification. Length 100mm (Peak Lupe 1972-100) is a combination instrument from Peak Optics consisting of a precision glass ruler and a 15× sliding loupe. The instrument:

  • Has a 100 mm usable measuring length (also available in 50, 200, 300 mm variants).
  • Has an etched scale with 0.1 mm graduation on clear glass.
  • Is supplied with a standard Peak 1962 15× loupe with achromatic lens.
  • Comes with an elegant carrying case.
  • Weighs only 43 g for the 100 mm model — hand-portable.
  • Compatible with EN ISO 17025 calibration certificate (at extra cost).

Basic specifications:

  • Manufacturer: Peak Optics (Japan)
  • Model: 1972-100 (100 mm variant)
  • Measuring length: 100 mm
  • Scale graduation: 0.1 mm (etched in glass)
  • Loupe magnification: 15×
  • Loupe field of view: 15 mm
  • Loupe optics: Achromatic, distortion-free
  • Size (100 mm): 140 × 25 × 3 mm
  • Weight (100 mm): 43 g
  • Delivery: In carrying case

Peak 1972-100 glass measuring ruler 100 mm with 15× loupe and 0.1 mm graduation

Etched glass scale — how it’s made

Precision glass rulers are manufactured through photoetching:

  1. A clear borosilicate glass plate is cleaned and coated with photoresist.
  2. The scale pattern is projected via a mask and UV exposure.
  3. Unexposed areas are washed away with etching solution.
  4. The glass is chemically etched where the pattern is — creating 5-10 µm deep grooves.
  5. The etched grooves are filled with black pigment.
  6. The surface is ground and polished to create an even contact surface.

The result: highly precision-rendered line patterns with a line thickness of 5-10 µm, a graduation error under 5 µm across the entire 100 mm span, and a completely flat glass surface that can be placed directly against the workpiece.

Combination glass ruler + loupe — how they’re used together

Practical measurement:

  1. Position the glass ruler so the scale’s zero point sits at one of the two measurement points on the workpiece.
  2. Verify that the scale is parallel to the line to be measured (rotate as needed).
  3. Place the loupe on top of the glass ruler so the loupe’s focal plane is level with the scale.
  4. Look through the loupe and read the scale value at the other measurement point.
  5. Count whole millimeters from zero + interpolate between graduation lines for the sub-mm value.

At 15× magnification, the 0.1 mm graduation appears as ~1.5 mm in the loupe’s field of view — clearly readable, and the operator can interpolate to 0.05 mm or better for in-between values.

Advantages over a mechanical caliper

Direct contact with the work surface: The glass ruler lies flat against the surface. No air gap, no angular offset.

No jaw geometry: Works on points, markers, cracks — where jaws cannot be applied.

Transparent reading: The operator sees both the scale and the workpiece at the same time.

Short measuring time: 5-10 seconds per measurement.

Repeatable: No operator force variation that could affect the value.

Easy to transport: At 43 g, it weighs less than a pen. Fits in a tool pocket.

Achromatic optics in the 15× loupe

At 15× magnification, chromatic aberration (color fringing) becomes noticeable with simple singlet lenses. The achromatic lens corrects this:

  • Two cemented elements (crown glass + flint glass).
  • Red and blue focus coincide at the same point.
  • Remaining green aberration is minimal.

Practical consequence: scale lines appear sharp and without color fringing, making precise reading possible even in poor lighting. Distortion-free means the scale lines are graduated perfectly straight — no curved lines that could lead to misreading.

The four Peak 1972 variants

Peak manufactures the 1972 series in four lengths:

  • 1972-50: 50 mm measuring length, 80×25×3 mm, 31 g.
  • 1972-100: 100 mm, 140×25×3 mm, 43 g.
  • 1972-200: 200 mm, 220×25×3 mm, 62 g.
  • 1972-300: 300 mm, 330×25×3 mm, 70 g.

Choosing the right length depends on the use case:

  • 50 mm: PCB measurement, microelectronics, watchmaking.
  • 100 mm: Standard workshop QC, the most popular format.
  • 200 mm: Larger workpieces, printed paper A5, sheet metal components.
  • 300 mm: A4 documents, technical drawings, larger sheet metal components.

Where a glass measuring ruler with loupe makes a real difference

PCB production and testing: Distance between components, hole center-to-center, trace thickness.

Damage documentation: Cracks in glass, car bodywork, sheet metal components for insurance and QC.

Printing and graphics industry: Registration marks, print registration, technical drawing verification.

Tool wear: Wear marks on cutting tools, drills, milling cutters.

Material testing: Crack analysis on metallurgical samples, crack patterns on ceramics.

Antique and art restoration: Damage measurement on paintings, banknotes, stamps.

Forensic investigations: Photo evidence measurement, document analysis.

Reverse engineering: Sufficient dimensional measurement of existing components for CAD.

Calibration reference: Verification of digital calipers and other measuring instruments.

Education: Metrology courses, technical training demonstrations.

Thermal stability of glass vs. steel

The glass ruler’s thermal expansion coefficient is considerably lower than steel’s:

  • Borosilicate glass: ~3.3 × 10⁻⁶ /°C.
  • Ordinary steel: ~11.5 × 10⁻⁶ /°C.
  • Stainless steel: ~16 × 10⁻⁶ /°C.

At 100 mm and a 5 °C temperature deviation:

  • Glass: 100 × 3.3 × 10⁻⁶ × 5 = 1.65 µm.
  • Steel: 100 × 11.5 × 10⁻⁶ × 5 = 5.75 µm.

Glass is 3.5× more thermally stable than steel — meaning the glass ruler can be used in environments with greater temperature variation without loss of accuracy.

Care and use

  • Cleaning: With isopropyl alcohol and a lint-free optical cloth. Never a rough cloth (can scratch).
  • Contact surface: Place the GLASS SIDE against the workpiece. The etched scale should be the facing-away side.
  • Avoid fingerprints: Hold only by the side edges.
  • Fall protection: Glass can break under impact. Always keep in the carrying case.
  • Solid work surface: Use on a clean, flat surface to avoid glass breakage under pressure.

What you get for your money

Peak Optics 1972-100 glass measuring ruler, 100 mm usable measuring length, etched scale with 0.1 mm graduation, clear borosilicate glass for see-through viewing, 15× loupe (standard Peak 1962 series) with achromatic distortion-free lens, 15 mm loupe field of view, hand-portable 43 g weight, elegant carrying case, compatible with EN ISO 17025 calibration certificate.

2,972 kronor is the instrument investment. Compared to a digital caliper 150 mm (500-1,500 kr, though it doesn’t work on non-raised reference edges), the glass ruler + loupe is the only practical solution for point-to-point measurement on a flat surface. Compared to a profile projector or optical measuring machine (30,000-200,000 kr, stationary), the Peak 1972-100 is hand-portable and fits in a tool pocket.

Read more: Peak 1972-100 glass measuring ruler with 15× loupe in the shop →

More news

All news